All Parts
Refine Search
NOS Parts can be indentified by the 7 digit number for example: 320 1284, which can be followed by a letter ocassionally. Parts indentified by a 6 digit hyphenated number (example: 12-0699) indicate an adequate supply of NOS Parts, a Reproduction part, or an Aftermarket manufactured replacement part. Very few used parts are listed. We hope to add more used parts in the future. At present you may contact us to inquire about used parts such as fenders, grilles, or any item you may need.
RING
Part #: 310 8190
1940-59 HEAD LAMP RETAINING RING, THIS IS THE STAINLESS STEEL RING THAT HOLDS THE BULB INTO THE BUCK..
$24.00
PLATE
Part #: 310 8241
1946-1967 SYNCHRONIZER ASSEMBLY PLATE, THREE USED PER SYNCHRONIZER. THIS IS THE PLATE (TAB) THAT RE..
$1.75
GROMMET
Part #: 310 8309
1941-50 GROMMET FOR THE GEAR SHIFT LEVER AT THE TRANSMISSION. NOTE: APPROXIMATE SIZE IS 3/4"OD X 5/1..
$12.75
SNAP RING .062"
Part #: 310 8318
1949-65 6 CYLINDER MODELS SECOND AND HIGH GEAR SYNCHRONIZER ASSEMBLY SNAP RING 0.062" THICK. NOTE: ..
$2.75
SNAP RING .062"
Part #: 310 8331
1949-65 ALL MODELS EXCEPT THOSE WITH THE 327 V8, OVERDRIVE UNIT REAR BEARING INNER RETAINING SNAP RI..
$2.75
LOCK PLATE
Part #: 310 8333
1941-63 LOCK PLATE FOR THE REVERSE IDLE SHAFT AND CLUSTER GEAR COUNTER SHAFT...
$3.00
GASKET
Part #: 310 8335
1940-1965 6 CYLINDER MODELS, TRANSMISSION FRONT BEARING CAP TO TRANSMISSION CASE GASKET. NOTES: FOR ..
$3.00
SNAP RING
Part #: 310 8336
1941-65 ALL MODELS EXCEPT WITH 327 V8, OVERDRIVE REAR BEARING SNAP RING (INNER & OUTER) 0.065" THICK..
$1.25
SNAP RING .065"
Part #: 310 8336
1946-65 ALL MODELS EXCEPT THOSE WITH THE 327 V8, OVERDRIVE UNIT REAR BEARING OUTER SNAP RING, 0.065"..
$2.75
SNAP RING .077"
Part #: 310 8338
1941-65 MAIN CASE FRONT BEARING (INPUT SHAFT) LOCK RING, 0.076" THICK. THIS IS LOCATED ON THE BEAR..
$2.75
SNAP RING .092"
Part #: 310 8339
1941-1965 6 CYLINDER MODELS, INPUT SHAFT BEARING SNAP RING, 0.092" THICK. THIS IS LOCATED ON THE SH..
$3.00
SNAP RING .098"
Part #: 310 8341
1946-65 6 CYLINDER MODELS, MANUAL TRANSMISSION MAIN CASE FRONT BEARING SNAP RING, 0.098" THICK, THIS..
$2.75
SNAP RING
Part #: 310 8346
1946-65 .068" THICK SNAP RING FOR THE OVERDRIVE REAR BEARING, INNER AND OUTER LOCATION...
$2.75
SNAP RING .071"
Part #: 310 8347
1946-65 ALL MODELS EXCEPT THOSE WITH THE 327 V8, OVERDRIVE UNIT REAR BEARING OUTER SNAP RING, 0.071"..
$2.75
REAR BEARING SNAP RING
Part #: 310 8406
1946-1965 0.090" THICK SNAP RING LOCATED ON THE 3-SPEED TRANSMISSION SHAFT IN MODELS WITHOUT OVERDRI..
$3.00
SNAP RING .093"
Part #: 310 8407
1948-59 SNAP RING, .093" THICK, THIS IS FOR THE SPEEDOMETER DRIVE GEAR...
$2.75
SNAP RING .096"
Part #: 310 8408
1941-65 OVERDRIVE UNIT FRONT BEARING INNER SNAP RING, .096" THICK. NOTE: 1965 MODELS THIS IS USED W..
$2.75
BEARING SHIM .080"
Part #: 310 8472
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.080". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .085"
Part #: 310 8473
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.085". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .090"
Part #: 310 8474
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.090". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .095"
Part #: 310 8475
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.095". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
CABLE
Part #: 310 8489
1941-48 SPEEDOMETER CABLE CORE. APPLICATION NOTES: 1941-42 MODEL 60 WITHOUT OVERDRIVE; 1941 MODEL 8..
$12.50
KEY
Part #: 310 8947
1941-1942 INDEX KEY FOR THE SHIFT LEVERS ONTO THE STEERING COLUMN SHIFT SHAFT. (REPLACES #310 6405,..
$8.75
SHAFT
Part #: 310 8985
1937-1938 SHAFT FOR THE TRANSMISSION CLUSTER GEAR. THIS REPLACES #310 3500...
$33.75
RING GEAR
Part #: 310 8993
1941-55 FLYWHEEL RING GEAR FOR MANUAL TRANSMISSION VEHICLES. NOTES: FOR 1941 MODELS THIS IS USED WI..
$27.75
GUARD
Part #: 310 9296
1941 FRONT OR REAR VERTICAL BUMPER GUARD. THIS IS NOT USED ON CABRIOLET REAR (61 & 81)...
$52.50
TRUSS ROD
Part #: 310 9343
1942-1948 TRUSS ROD, DIFFERENTIAL TO TORQUE TUBE. ON MODELS WITH 3-SPEED TRANSMISSION (NO OVERDRIVE)..
$94.75
HOUSING
Part #: 310 9683
1941-48 DRIVESHAFT CENTER BEARING HOUSING WITH BUSHING. NOTE: FOR 1941 MODELS STARTING AT BODY N4-51..
$44.50
IGNITION COIL
Part #: 311 0518
1936-1949 IGNITION COIL FOR MODELS HAVING AUTO-LITE SYSTEM. NOTE: THIS IS A STANDARD IGNITION REPLAC..
$47.75
LENS
Part #: 311 1004
1942-1948 RED STOP LENS AT THE LICENSE PLATE LAMP (GLASS). (REPLACES #310 5651)..
$39.75
GASKET
Part #: 311 1263
1937-1962 CORK O-RING GASKET FOR THE SPEEDOMETER CABLE AT THE TRANSMISSION. NOTES: 1958 ALL RAMBLER ..
$3.00
BRACKET
Part #: 311 1268
1940-41 REAR STABILIZER BRACKET LOCATED ON THE LEFT BRAKE BACKING PLATE. (REPLACES #310 5409)..
$14.75
GRILLE
Part #: 311 1437
1942 UPPER GRILLE. THIS IS THE PAINTED TYPE INTRODUCED AS PART OF THE WAR MANUFACTURING CHANGES...
$124.75
PIVOT BAR
Part #: 311 1766-B
1941-1951 LOWER CONTROL ARM PIVOT BAR WITHOUT THE PIVOT BUSHINGS...
$39.00
TUBE
Part #: 311 1792
1940-51 OIL PUMP PICK-UP TUBE AND SCREEN ASSEMBLY. (LATER NUMBER = 312 3521)...
$18.50
MAIN BEARING SET
Part #: 311 1812
1940-1941 40 MAIN BEARING SET, .010". THIS SET HAS HAD WATER/MOISTURE EXPOSURE. (REPLACES #310 829..
$29.75
SPIDER GEAR SET
Part #: 311 1911
1949-1959 MODELS WITHOUT LIMITED SLIP OPTION, DIFFERENTIAL SIDE GEAR SET. NOTE: FOR 1957 RAMBLER ..
$89.75
WIRE
Part #: 311 1942
1942-48 MODELS WITH AUTOLITE DISTRIBUTOR #IGS-4205, IGS-4205A OR B. THE DISTRIBUTOR GROUND WIRE (LE..
$1.25
END PLATE
Part #: 311 2011
1946-1948 DRIVE END PLATE WITH BUSHING FOR THE AUTOLITE STARTER MOTOR. NOTE: 1948 USED ON ENGINES P..
$27.75
BEARING SHIM .082"
Part #: 311 2014
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.082". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BERING SHIM .084
Part #: 311 2015
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.084". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .086"
Part #: 311 2016
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.086". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .088"
Part #: 311 2017
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.088". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .092"
Part #: 311 2018
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.092". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .094"
Part #: 311 2019
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.094". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .096"
Part #: 311 2020
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.096". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
BEARING SHIM .098"
Part #: 311 2021
1941-60 DIFFERENTIAL SIDE BEARING SHIM, 0.098". NOTE: FOR 1960 MODELS THIS IS USED IN MODELS HAVIN..
$2.75
REPAIR KIT
Part #: 311 2078
1946-1947 REPAIR KIT FOR CARTER WA611S 1-BARREL CARBURETOR. THIS KIT IS BY SORENSEN. THEIR #CK-116...
$22.75
SPEEDOMETER GEAR
Part #: 311 2156
1946-1963 OVERDRIVE TRANSMISSION DRIVE GEAR ON THE MAIN SHAFT. NOTE: 1961-1963 AMERICAN MODELS WITH ..
$24.75
DRIVE GEAR
Part #: 311 2157
1946-69 OVERDRIVE GOVERNOR DRIVE GEAR FOR ALL MODELS EXCEPT WITH 327 OR 343 V8...
$19.00
WASHER
Part #: 311 2293
1949-66 RETAINING WASHER FOR THE CLUSTER GEAR NEEDLE BEARINGS. NOTE: 1963-66 THESE ARE USED WITH 23..
$0.50
MAIN BEARING SET
Part #: 311 2397
1947-1948 MAIN BEARING SET, .002". THIS IS USED IN ENGINE NUMBER KE26606 AND HIGHER. THIS BEARING SE..
$21.75
PLUNGER
Part #: 311 2400-B
1947-1964 6 CYLINDER OIL PRESSURE RELIEF PLUNGER. NOTES: THIS IS NOT USED IN 1961-1964 MODELS WITH T..
$23.00
REPAIR KIT
Part #: 311 2534
1948-1959 REAR WHEEL CYLNDER REPAIR KIT. NOTE: 1957 MODELS THIS IS USED ON MODELS WITH ECCENTRIC BRA..
$8.00
SHIFT SHAFT
Part #: 311 2536
1946-48 SHIFTER SHAFT THOUGH THE TRANSMISSION CASE FOR LOW/REVERSE...
$15.00
GROUND STRAP
Part #: 311 2555
1950-54 GROUND STRAP FROM TIMING COVER TO RIGHT ENGINE SUPPORT ON CONVERTIBLE MODELS. (THIS REPLACE..
$18.00
GEAR SHIM .003"
Part #: 311 2620
1946-60 DIFFERENTIAL SIDE GEAR SHIM, 0.003" THICK. NOTE: FOR 1960 MODELS THIS IS USED WITH 16 SPLI..
$2.75
GEAR SHIM .005"
Part #: 311 2621
1946-60 DIFFERENTIAL SIDE GEAR SHIM, 0.005" THICK. NOTE: FOR 1960 MODELS THIS IS USED WITH 16 SPLI..
$2.75
PINION SHIM .010"
Part #: 311 2622
1946-60 DIFFERENTIAL PINION BEARING SHIM, 0.010" THICK (1 41/64" INSIDE DIAMETER). NOTE: FOR 1960 ..
$2.75
ROTOR
Part #: 311 2718
1948-55 DISTRIBUTOR ROTOR. NOTE: FOR 1955 MODELS WITHOUT THE DUAL CARBURETOR OPTION...
$14.00
SHACKLE
Part #: 311 2750
1946-48 LEAF SPRING RIGHT REAR SHACKLE ASSEMBLY. (REPLACES #310 7883, ALSO REPLACES #312 3483)..
$44.00
MAIN BEARING SET
Part #: 311 2785
1949-1956 STATESMAN MAIN BEARING SET, STANDARD. THIS IS AN NOS PART AND IS LIMITED TO STOCK ON HAND...
$59.00
PULLEY
Part #: 311 2795
1949-50 GENERATOR FAN/PULLEY FOR MODELS WITH 3/4" FAN BELT AND DELCO #1102702 OR 1102712 GENERATORS...
$19.00
ROD BEARING (1)
Part #: 311 2851
1949-1951 ROD BEARING +.002" OVERSIZE. THIS IS A SINGLE ROD SET, NOT A FULL SET FOR ALL 6 RODS...
$12.00
